Guide · Homeowners · 3 min read · Updated 17 November 2026
Dry Rot vs Wet Rot: Differences, Signs and Treatment
Short answer
Dry rot, caused by Serpula lacrymans, can spread beyond the original wet area and across masonry to reach new timber, so it needs wider investigation and treatment. Wet rot, usually caused by Coniophora puteana, only attacks timber that stays very wet and stops once the timber dries. Both need the moisture source fixing, but dry rot outbreaks are generally larger and more expensive to repair.
Two different problems
Dry rot and wet rot are both forms of fungal decay that break down timber. Both start because wood has become damp. But they behave differently once they start, and that changes how they are treated and how much the repair costs. Getting the identification right is important, because treating wet rot as dry rot can lead to unnecessary destruction and expense, while missing dry rot can let it spread unchecked.
Wet rot is much more common. Most rotten window sills, door frames, fascias and decayed joist ends are wet rot. Dry rot is less common but more serious.
The two are often confused because both leave timber soft, cracked and discoloured, and both thrive in damp, poorly ventilated spaces. The key questions a specialist asks are how wet the timber is, whether the fungus has spread beyond the wet area and what the fungal growth looks like.
Side-by-side comparison
The table below summarises the main differences. A specialist will look at several of these features together before confirming which type of rot is present.
Moisture content gives a useful clue. Wet rot generally needs timber to be much wetter than dry rot does, so dry rot can sometimes be found in timber that feels only slightly damp, often next to masonry that is feeding it with moisture.
| Feature | Dry rot | Wet rot |
|---|---|---|
| Main fungus | Serpula lacrymans | Often Coniophora puteana, also others |
| Moisture needed | Damp timber, can then spread to drier areas | Timber that stays very wet |
| Spread | Can travel over and through masonry | Confined to the wet area |
| Growth | White mycelium, grey strands, pancake fruiting body | Dark strands, few fruiting bodies |
| Decayed timber | Dry, brown, large cube-shaped cracks | Darker, softer, cracking along the grain |
| Typical locations | Under floors, behind plaster, cellars | Sills, frames, fascias, joist ends |
| Treatment scope | Wider opening up and targeted masonry treatment | Local repair once moisture is fixed |
How dry rot behaves
Dry rot needs damp timber to get started, but once it is growing it can produce strands that carry moisture and nutrients, allowing it to spread across brickwork, through mortar joints and behind plaster to find new wood. It is common in poorly ventilated spaces such as under suspended floors, in cellars and behind panelling, where moisture levels are high and air is still. Its fruiting bodies release large amounts of rust-red spores.
Because of this spreading ability, treatment involves finding the full extent of the outbreak, removing decayed timber and isolating new timber from damp masonry.
How wet rot behaves
Wet rot needs timber to stay very wet for a long time. It is common where water is trapped against wood: at the bottom of window frames, on sills, at door frame feet, on fascia boards behind blocked gutters and at joist ends sitting in damp walls. When the timber dries, the wet rot fungus stops growing. It does not cross masonry to find new timber in the way dry rot can.
Treatment focuses on fixing the moisture source and cutting out and replacing or resin-repairing the decayed sections.
- Rotten window sills and bottom rails
- Door frame feet and thresholds
- Fascias, soffits and bargeboards
- Joist ends in damp walls
- Timber near leaking pipes or bathrooms
Treatment and cost differences
Both types of rot need the source of moisture found and fixed first. For wet rot, that is often followed by a relatively simple repair, such as cutting out decayed timber and splicing in new wood or using an epoxy resin repair. For dry rot, the work is usually broader: opening up floors and walls to trace the fungus, removing decayed timber, treating surrounding timber and masonry with fungicide where needed and replacing structural timbers with pre-treated wood.
That is why dry rot repairs tend to cost more. A small dry rot outbreak typically costs £1,000 to £2,500, a single room with floor joists £3,000 to £7,000, and larger structural outbreaks £7,000 to £20,000 or more. Most wet rot repairs to joinery cost far less.
When you need a specialist
If you find soft or crumbling timber, a professional should confirm the type of rot, especially where structural timbers are involved or you see strands, fluffy growth or red spore dust. A specialist dry rot survey costs £200 to £450 and maps the outbreak and its cause. For simple wet rot in a sill or door frame, a joiner can often diagnose and repair it directly. Either way, fixing the source of moisture is the essential first step.
Whichever type is found, the cost of delay is real. Both types of rot keep growing while the timber stays damp.
Other wood-decay problems
Not all decayed timber is caused by dry rot or brown wet rots. White rots bleach timber and leave it soft and stringy rather than cracked into cubes. Wood-boring insects, such as common furniture beetle, leave small round exit holes and fine dust, and are often found alongside damp and decay because they prefer moist wood. A specialist survey will look for all of these, since each needs its own approach.
Surface moulds are another frequent cause of alarm. They grow on damp timber and plaster, often as black, green or white patches, but do not decay the wood. They are a sign of damp conditions that should be fixed, not of structural damage.
Questions people also ask
Which is worse, dry rot or wet rot?
Dry rot is generally more serious because it can spread beyond the original wet area and across masonry to reach new timber. Wet rot is more common and usually stays where the timber is wet. Both can cause structural damage if left long enough, especially in floor joists and roof timbers.
Can wet rot turn into dry rot?
No. They are caused by different fungi. However, the same damp conditions can support both types, and it is possible for a property to have wet rot in one area and dry rot in another. A specialist survey will identify each outbreak separately.
Do both types of rot need chemical treatment?
Not always. Wet rot usually stops once the timber dries, so the main work is fixing the moisture and replacing decayed wood, with preservative used on nearby timber where appropriate. Dry rot may need targeted fungicide on timber and masonry, but modern practice focuses on removing moisture and decay rather than extensive spraying.
Written and checked by the Dry Rot Treatment team. Read our editorial policy.
More guides
How Much Does Dry Rot Treatment Cost in the UK?
Dry rot treatment in the UK costs £1,000–£2,500 for a small localised outbreak, £3,000–£7,000 for a single room with floor joists and £7,000–£20,000…
How to Identify Dry Rot: Signs, Simple Tests and What to Do
Dry rot shows as brown, crumbly timber with deep cube-shaped cracking, white cotton-wool or grey sheet-like growth, thick grey strands that can cross…
What Happens During Dry Rot Treatment? Stage by Stage
Dry rot treatment follows clear stages: a survey to confirm the fungus and map its extent, fixing the moisture source, opening up floors and walls,…
Dry Rot in Listed and Period Buildings: A Conservation Approach
In listed and period buildings, dry rot is best treated by fixing the moisture source, drying the structure and removing only decayed timber, rather…
Get a free dry rot treatment quote
Tell us what you need and we'll come back with a clear price.
Request a quote