Guide · Homeowners · 3 min read · Updated 17 November 2026
What Happens During Dry Rot Treatment? Stage by Stage
Short answer
Dry rot treatment follows clear stages: a survey to confirm the fungus and map its extent, fixing the moisture source, opening up floors and walls, removing decayed timber and contaminated material, targeted fungicide treatment of timber and masonry, fitting pre-treated replacement timber isolated from damp walls, then drying out, replastering and reinstatement. Modern practice prioritises drying the building over heavy chemical use.
Stage 1: Survey and diagnosis
Treatment starts with a specialist survey. The surveyor confirms the fungus is dry rot rather than wet rot or a surface mould, identifies the moisture source and maps the extent of the outbreak as far as possible without major opening up. A dry rot survey and report costs £200 to £450. The report should include photos, a plan of affected areas, the likely cause and a recommended scope of work.
Because dry rot often hides behind plaster and under floors, the surveyor may recommend limited exploratory opening up, such as lifting boards or removing small areas of plaster, before the full scope is agreed.
Stage 2: Fix the moisture source
Dry rot cannot survive without damp. Finding and fixing the source of water is the single most important part of treatment. Common sources include leaking gutters and downpipes, roof defects, failed flashings, plumbing leaks, bridged damp courses and blocked air bricks under suspended floors. Without this step, any other treatment is likely to fail.
Once the source is fixed, the structure needs to dry. Contractors may use ventilation, fans or dehumidifiers to speed this up, and sub-floor ventilation is often improved by clearing or adding air bricks.
Some contractors fit moisture sensors in walls or timbers at this stage so that drying can be tracked over the following weeks. These readings show when it is safe to replaster and refit joinery, and give useful evidence if questions arise later.
Stage 3: Opening up and removing decay
Next, the affected area is opened up so the full extent of the fungus can be seen. Floorboards are lifted, skirtings and panelling removed and plaster hacked off where the fungus has spread behind it. Decayed timber is cut out and removed from the property, along with fungal growth and debris. Traditional practice was to cut back a set distance beyond the last visible sign of decay, often quoted as around a metre. Many specialists now take a more targeted approach, removing what is decayed and relying on drying and isolation to control the rest, which preserves more of the building.
- Lift floorboards and remove skirtings and panelling
- Hack off plaster where strands have spread behind it
- Cut out all decayed timber and remove it from site
- Clean fungal growth and debris from masonry
- Record the extent of decay with photos
Stage 4: Treatment of timber and masonry
Where needed, remaining sound timber nearby is treated with a preservative, and masonry the fungus has crossed may be treated with a fungicide to limit regrowth. Products must be authorised biocides for use in Great Britain, and the operatives must follow the Control of Substances Hazardous to Health Regulations 2002, assessing and controlling exposure according to product safety data sheets. Modern treatment is targeted rather than blanket spraying.
In some cases, masonry is irrigated through drilled holes, or a fungicidal render or plaster additive is used, but these steps should be justified by the extent of the outbreak.
| Stage | Typical duration | Key point |
|---|---|---|
| Survey and report | Visit plus a few days | Confirms dry rot and the moisture source |
| Fix moisture source | Varies | Essential for lasting success |
| Opening up and removal | 1–5 days | Reveals the full extent |
| Targeted treatment | 1–2 days | Authorised products, COSHH controls |
| New timber and isolation | Several days | Pre-treated timber kept off damp masonry |
| Drying and replastering | Weeks to months | Walls must dry before final finishes |
Stage 5: Replacement timber and reinstatement
Structural timbers such as joists, wall plates and lintels are replaced with pre-treated timber. Joist ends are often isolated from damp walls using damp proof membranes, joist hangers or new bearings so they cannot pick up moisture in future. Where large structural elements are affected, a structural engineer may design temporary support and permanent repairs.
Once the walls have dried sufficiently, they are replastered at £60 to £130 per m², often with lime in older buildings. Floors, skirtings and joinery are refitted and the room redecorated with breathable finishes while drying continues.
After treatment
Keep the building dry and ventilated. Make sure gutters stay clear, air bricks remain open and any leaks are fixed promptly. Keep the survey, treatment record and any guarantee safe, as buyers' solicitors will ask for them. If you notice a musty smell, new fungal growth or red spore dust in future, contact the contractor straight away. Early action is far cheaper than dealing with a second outbreak.
Expect the house to feel damp and smell slightly of new plaster for a while after the work. This fades as the walls dry. Keep heating gentle and ventilation steady rather than blasting heat, which can crack new plaster.
Choosing a dry rot specialist
Look for a contractor who explains the cause of the outbreak, not just the treatment. They should talk first about the moisture source, show you the decayed timber they plan to remove and explain how new timber will be protected. Ask whether the surveyor holds a recognised remedial qualification, such as the Certificated Surveyor in Remedial Treatment from the Property Care Association, and whether the firm carries public liability insurance.
Ask too how they will deal with structural timbers, whether an engineer is likely to be involved and what guarantee is offered, including whether it is insurance-backed.
Questions people also ask
Do I need to cut out a metre of timber beyond dry rot?
That was traditional advice, but many specialists now take a more targeted approach. They remove all decayed timber, fix the moisture source, dry the structure and isolate new timber from damp masonry. A cut-back margin may still be used where the fungus is active, and the survey should explain the approach.
Can I live in my house during dry rot treatment?
Usually yes, although the affected rooms will be out of use and there will be dust and disruption. If treatment chemicals are used, follow the contractor's guidance on keeping rooms ventilated and staying out of treated areas for the stated period. Larger structural repairs may need temporary arrangements.
Does dry rot come back after treatment?
Dry rot is unlikely to return if the moisture source is fixed and the building is kept dry and ventilated. Most recurrences happen because the original leak was not fully resolved or a new one has developed. Regular maintenance of roofs, gutters and plumbing is the best protection.
Written and checked by the Dry Rot Treatment team. Read our editorial policy.
More guides
How Much Does Dry Rot Treatment Cost in the UK?
Dry rot treatment in the UK costs £1,000–£2,500 for a small localised outbreak, £3,000–£7,000 for a single room with floor joists and £7,000–£20,000…
How to Identify Dry Rot: Signs, Simple Tests and What to Do
Dry rot shows as brown, crumbly timber with deep cube-shaped cracking, white cotton-wool or grey sheet-like growth, thick grey strands that can cross…
Dry Rot vs Wet Rot: Differences, Signs and Treatment
Dry rot, caused by Serpula lacrymans, can spread beyond the original wet area and across masonry to reach new timber, so it needs wider investigation…
Dry Rot in Listed and Period Buildings: A Conservation Approach
In listed and period buildings, dry rot is best treated by fixing the moisture source, drying the structure and removing only decayed timber, rather…
Get a free dry rot treatment quote
Tell us what you need and we'll come back with a clear price.
Request a quote